BMX

Traditional chain pins are 3mm in diameter. The Key Chains are 5mm, and they are available with a hollow or solid pin assembly. These oversized pins are 4 times stronger than traditional pins, and the chances of bending one, whether the pin is hollow or solid, are essentially zero. The 5mm riveted pins provide added strength, but they also provide a bigger contact surface with the chain’s plates, which makes them harder to push out or bend. The hollow pin assembly, by design, allows for a stronger rivet connection to form during manufacturing, resulting in a stronger chain overall. Each plate has a low profile and an extra narrow waist that makes it harder to catch the plates at unwanted times. At 1.4mm, the plates are substantially thicker than the plates of any other chain, and they’re also more than 50% harder to bend than the thickest existing 1.2mm chain plates too. Users can break and re-join the chain with just a 3mm hex key. The chain’s half link plates are taller at the bends to both increase stiffness and minimize stretch. Since the use of a chain breaker to re-join the chain has been eliminated, the pins can retain their original level of tightness from the factory. Also, carrying a spare master link and 3mm allen key in most cases is enough to repair the Key Chain when riding, so lugging around a chain tool is usually unnecessary. By using material as efficiently as possible, Odyssey has strengthened every component of the chain and kept the weight in the same range as their Bluebird chain. Stretching of the chain is minimized by using a standard alternating plate pattern and limiting the chain to a single, beefed up half link. This configuration maximizes the lifespan of the sprocket and driver. - Width: 1/8-inch

Top your seat with Black Label's Pivotal Seat Cover. It's slim, light, and has great-looking graphics. It's made of durable vinyl with thin padding so it's ready for all types of riding.

Shimano's DXR V-Brake Levers are the choice of the pros, from the Olympics to the local race scene. They use a 2-finger design with Shimano's proven Super Linear Response system that gives you great power and feel with little effort.

WeThePeople's Tripod Seatpost is made from strong, lightweight 6061 aluminum. The Tripod design is stronger and has more structural support than Pivotal seat/post combos. It uses a 3-point mounting system, where two rear supports press into channels underneath a Tripod seat, and a single bolt up front secures the system.

Check out the dinosaur skin-like texture of WeThePeople's Raptor grips! Like a raptor, you can wrap your claws around these grips and let the good times roll. The soft, VEX rubber compounds conforms perfectly to your hand, and holds up great to long days on the bike. • 150mm Long, 27.8mm Diameter • 30 durometer rubber • Low flange design • Includes WeThePeople nylon barends

WeThePeople's Arrow 146 Grips have the perfect texture and density to give you newfound confidence while railing it on the bike. Material: VEX rubber compound Size: 146mm x 28mm Specials: soft angled rib design with medium-sized flange; includes WeThePeople nylon barends

WeThePeople's Arrow 115 Grips have the perfect texture and density to give you new confidence while railing it on the bike. Material: VEX rubber compound Rubber durometer: 30° Size: 115mm x 28mm Specials: soft angled rib design with medium-sized flange; includes WeThePeople nylon barends

WeThePeople's Socket Pivotal seat post is made from 6061 aluminum for a perfect blend of strength and weight savings. It works with all Pivotal seats and comes in the perfect color and size to match your bike. Plus, there's a 17mm socket head built into the bottom of the post for park-side adjustments to your wheels.

Ground breaking riding deserves a fork so burly fork that it can literally break the ground, should the need arise. WeThePeople's Sterling fork is masterfully crafted to meet the insane demands of team rider, Pete Sawyer. The Sterling can handle it all, and it looks good doing it. Find a matching color scheme on the Sterling signature frames too! • Material: Full-liquid post heat-treatment on 4130 “M2“ chromoly • Steerer Length: 170mm • Offset: 32mm • Dropout: 6mm laser cut & CNC machined, heat-treated 4130 chromoly, 3/8'' axle • Fully CNC’d steerer, single butted integrated crown race designed to work with integrated headsets with a 45° bearing

Aaron’s signature tires feature an updated block tread and bigger sizing. The uniform block tread is reminiscent of his original tire, but freshened up. Coming in at 20x2.30" and 20x2.40"

Mike Aitken's popular signature tires for street and dirt. Ideal for use at high speeds. - 20 × 2.25, and 20 x 2.45 Dual ply casing

The Evo 2 brake is the industry leading U-brake because of its modular hardware features and affordable value. Install it as a rear brake or front brake straight out of the box. Comes with Odyssey’s convenient double lugged straddle cable, custom curved cable hanger and an array of hardware for adapting the brake to every possible set-up. Forged from aluminum for strength, and to avoid unnecessary upcharges from frivolous CNC machining. The Evo 2 is the natural progression of the original Evolver. It has seen constant refinement and new running changes to keep it as the standard in BMX braking. This design allows for a seemingly limitless amount of cable installation options, while remaining equally powerful as both a front OR rear wheel brake. New forge tooling was created that provides for a sleeker side profile. Arms are forged prior to machining for strength and durability. Contrary to the uneducated in metallurgy, a forged metal piece is of much higher strength than a piece machined from a block of material. FEATURES: - All of the cable set screws are now flat-tipped to prevent excess damage to the cable’s inner wire - Cable lugs are smaller and use a 10 mm hex head - Pre-lugged straddle cable is shorter - Front cable adapter is smaller and made of aluminum - Flush surfaces, with the lowest possible overall stack height - Front or rear wheel use - Redesigned brake pads - Two sets of springs (hard and soft for custom tension/modulation) - Spring tension indicators (easy set up) - Newly designed straddle hanger

6061 aluminum with precision sealed mechanism bearing and lower (17mm) stack height.

- For 19mm crank spindles and threaded Euro bottom bracket frames. - High-quality four bearing design with aluminum cups.

Odyssey's 49er is a traditional-looking 4-piece bar that uses multi-butted main tubing, traditional 7/8" crossbar for strength, larger radius bends for greater durability, and welded end caps to reduce flex. These bars have a post-weld heat-treating which is guaranteed against manufacturer’s defects. SPECS - 9-inch Rise - 29-inch Width - 1.5° Upsweep - 12° Backsweep - 2lbs 3.4 oz

One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable too. The Ghost Pad addresses the hassles of brake pad installation by eliminating the traditional dome shaped washers used for toe-in. The pad improves stiffness by building the toe-in into the pad shape and utilizing a solid extruded aluminum frame at its core. The Ghost Pad’s assembly consists of simply lining it up with the rim and tightening down an M6 female bolt. Comes stock on the Springfield brake. SPECS Hardware: - In-bound bolt, 5mm Hex Key, M6x1.0 Thread - Pad Material: Black (standard) or Clear Rubber (Soft) - Weight: 1.0oz / 28g (pair)

The 4.5-inch peg features a full 4130 core with a long-lasting, fast-sliding, plastic sleeve. - Sold individually - 14mm with 3/8” adapters only - Replacement sleeves sold separately - 4.5" (length) x 1.5" (outer diameter) - 4.5 oz (9 oz for a pair)

Odyssey's original dual cable detangler system has been the industry standard since day one. Odyssey has been making the Gyro since 1986 and constantly improving it along the way. Everything you need to run a Gyro. Odyssey Gyro cables and upper and lower cable stops included.

It’s a traditional straight up pivotal design with a 200mm length.

This custom 7075-T6 aluminum pre-load bolt design is included with every Odyssey fork. - Fits both a 6mm and 8mm allen key. - Front brake cable thru-way hole for removal without disconnecting brake hardware. - Designed with an easy-cut thread groove if you cut your fork’s steerer tube down.

Designed specifically for use with Odyssey's Quartet FRONT or REAR hubs. SPECS - Forged from 7075-T6 aluminum for greater strength and durability - Steel insert prevents guard deformation, prolonging bearing life

New dust cap design, with Monogram laser etched logo, for a cleaner look to accommodate a taller riding set up with less spacers. Same quality as Odyssey's Pro Headset using high-quality sealed bearings and a precision tapered wedge to keep the headset tight at all times. FEATURES - High-quality sealed bearings. - Color matched spacers included. - 15mm dust cap. With 3mm, and 2mm spacers - Laser etched Odyssey bearings. SPECS - Campagnolo standard spec. - 1 1/8-inch integrated headset. - 45º tapered bearings - 41.8mm outer diameter (fits 42mm BMX head tubes).

A huge leap forward in pedal technology that results in a simpler overall design. Extremely lightweight plastic bodies eliminate the need for bearings and allow for a spindle that is significantly stronger than normal. Metal pins make the pedal very grippy, and the pedal will still function normally when pins are removed from one side for grind tricks. No flimsy outboard end caps. Pedal body halves are easy and inexpensive to replace – instead of replacing the whole pedal. - 9/16-inch, heat-treated, 4140 chromoly spindle - Proprietary high-strength plastic composite

The Monolever was an instant classic and has become a clear favorite with pro riders around the world because of its familiar feel, smooth edges and variety of handle options.

- 4140 Chromoly - 3 Possible peg positions for longer peg life - 14mm with 3/8-inch adapters included - 4 inches (length) x 1-3/8 inches (outer diameter) - Sold in pairs - 8.75 oz (17.5 oz for a pair)

The M2 lever works with a single cable or Odyssey’s patented dual cable system. The M2 cable system improves braking power for GYRO users. - Right hand only (works flipped on the left) - M2 specific upper cable and single cable coupler included.

Compatible cable for M2 Monolever.

The Odyssey K-Shield Linear cable features a pre-stretched inner Slic Kable covered in a linear casing to prevent binding and an outer K-Shield mesh housing for less weight over a standard steel mesh housing. (2.9 oz)

This is Odyssey's top-of-the-line brake cable that ties together all of their most advanced braking technology. - Utilizes the original BMX Linear Slic Kable housing to prevent binding when the bars are rotated. - Factory installed ferrule ends with inner volcano shape to prevent housing blow out; a Linear Slic Kable standard since 2008. - Specially coated inner wire for ultra low friction, a proven feature resurrected from their once famous Brakeline cables. - Gyro lug included at one end of the inner wire for use with detanglers. - 60-65mm in length.

A total redesign of Odyssey's popular MDS sprocket. With a built-in full guard, this sprocket lives up to its name, helping to protect your chain from anything you can throw at it. Sprocket thickness increases towards the guard area for greater strength. Compatible with all chain widths. - 7075 Aluminum